Sunday 30 September 2018

The Haunted Lighthouse from Tin-Soldier

Introduction

For some time now I have been looking for a lighthouse model that I can use with my 28mm figures.  This would play a vital role in certain Pulp-style games as the lonely rendezvous for a spy and his/her handler, or as a focus for a raid by Nazis/aliens/sea monsters/...

I did consider converting a bedside lamp.  Yes, apparently you can buy table lamps in the form of a lighthouse!  However, they're (a) a bit too expensive for this type of project and (b) often quite kitsch - not very realistic representations of anything found in the real world.

It took a long time, but my hunt is now over.  I discovered that Tin Soldier publish a range of slightly unusual paper models to download and print; amongst these is a "Haunted Lighthouse".


The Kit


For a mere $10 (US), I bought the kit and downloaded the resulting PDF.  It's taken me about a week to build this kit, though note that this could be done a lot quicker if desired:

  1. I was only spending an hour or two after work on this project most days.
  2. My version of the kit has a lot of reinforcement and other adaptations to make it stronger and more suitable for the games table.  This extra work did add to the construction time.
Other observations about the kit:
  • I found that I wanted some parts in paper, but others in card or even on a transparency.  Initially, I printed the entire PDF onto paper without thinking; this did waste some sheets.
  • Sometimes, the pieces I wanted on card were on the same page as others that I intended to print onto paper.  This is not unusual in paper modelling, but again it leads to waste as the same sheet needs to be printed onto both the thinner and the thicker materials.
  • The instructions were comprehensive, but largely written in prose rather than drawn as schematics or build stages.  There's nothing wrong with that, but it is harder to follow, I think.  As an experienced card modeller, I didn't need to refer to the instructions very often anyway; the sequence and location of most parts was fairly obvious.
  • Pieces fitted together well; I didn't have to make any changes to the basic shape and form of the model.

The Build

The first thing to say about my version is that I cut out an MDF base for the building.  This is slightly larger than the supplied (printed, coloured) ground and will be stronger & heavier than a foam core base.  It should make the whole assembly a bit more stable, especially considering the height of the tower.  I then painted and textured the base to fit in with my other terrain pieces, so the base you see in these pictures is quite different from that supplied with the kit.



So, here's the next adaptation: I didn't glue the tower to the base.  Instead, there is a rare earth magnet at the bottom of the tower and an iron washer buried in the MDF base.  Together, these hold the tower in place very well, whilst still allowing it to be removed for storage.



I made the roof as a separate piece too.  This allows access to the inside, though note that the kit does not supply textures for interior walls.  Instead, the inside is entirely my own work; it was easy enough for me to reuse parts from other kits or to download free wallpapers for dollhouses (look for 1/4" scale if you intend to do this as most dollhouses are intended for much larger figures).



Here's another adaptation: the top platform is separate from the main tower.  This uses a simple plug & socket joint; the socket is 3" of solid cardboard tube from some packaging or other, glued firmly into the upper part of the tower.

Whilst on this part, note that the railing around the platform is especially fiddly to build from paper & card; it's easily the most difficult part of the entire project.  I did consider very seriously trying to scratch build a replacement from wire and/or balsa, but in the end I went with the printed parts.



It's a lighthouse, so I couldn't resist making one final adaptation.  I embedded a cheap LED "pen" torch into the upper part (it's the "plug" part from the previous picture).  I added a clear plastic bead glued to the top to help redirect the light and then glued a plastic cap from a drinks bottle over that.  Yes, it does light up!  At night time it seemed very bright, though in this daytime photograph it's not so strong.


Conclusion

I'm delighted with this model!  It's certainly unique and should lead to some interesting games.  The kit didn't cost much in terms of money or materials, though it did take a certain amount of construction time, as all paper/card builds do.

Although it's described as a "haunted" lighthouse, there's nothing particularly spooky about it other than the derelict roofs and optional, grimy version of the lantern room.  Indeed, if the kit offered alternate, "clean" roofs then I think this could make an excellent working building instead.

22 comments:

  1. That looks absolutely brilliant! Can't wait to see it in a game 🙂

    ReplyDelete
    Replies
    1. Thanks, Ivor. As for the game, I do have a plan...

      Delete
  2. Very nice! I find with paper models a spot of matt varnish makes them look, at least from a gaming distance, almost the same as any other model.

    ReplyDelete
    Replies
    1. Hmm, I did consider varnishing the model. However in the end I decided that it didn't need such treatment.

      Delete
  3. Brilliantly done sir and that light! Epic

    ReplyDelete
    Replies
    1. The light really is a lot brighter in real life than it looks in the photo :-) . Thanks.

      Delete
  4. Fab job dude it has turned out marvellous!

    ReplyDelete
    Replies
    1. Glad you like it, Simon. I tend to agree: it's a rather splendid model :-) !

      Delete
  5. A most impressive piece of scenery. I do like what you've done to it.

    ReplyDelete
    Replies
    1. Thanks, Bryan - I am rather pleased with it. Having said that, I'm absolutely certain that you or a number of others would be capable of turning out a nice model from this kit as well.

      Delete
  6. Replies
    1. Thanks, Frank. I will admit to being rather pleased with this one :-) .

      Delete
  7. It's definetly an impressive model and the addition of the intergrated houses really makes it for me.

    ReplyDelete
    Replies
    1. The attached "keeper's cottage" is a very likely feature in real life, at least for a coastal lighthouse (as opposed to something built on a small rock in the middle of the sea!). Thanks, Joe.

      Delete
  8. Very nice. I'll be very wary of safari snipers if that particular building shows up.

    ReplyDelete
    Replies
    1. Hah, I think that Sir Henry's Safari would be quite lost if they ended up anywhere near this lighthouse :-) .

      Delete
  9. Excellent. I could go on but that sums it up.

    ReplyDelete
    Replies
    1. Thanks, Clint. Sometimes that's all that needs to be said.

      Delete
  10. Looks superb, realistic and very impressive!

    ReplyDelete
  11. That's an impressive lighthouse. It reminded me of the one in the movie 'The Light Between Oceans' starring Michael Fassbender and Alicia Vikander. As such it would also make an excellent terrain piece for a diorama if suitable 28mm miniatures could be found.

    ReplyDelete
    Replies
    1. I'm not familiar with that film & book, but lighthouses like this are to be found in many parts of the world. It is a nice kit, isn't it :-) ?

      Delete